MR-10 geodesic satellite multi-frequency equipment


The multi frequency satellite geodetic equipment МР-10 is intended for surveying research, supervision of building process, high accuracy positioning during creation and development of reference geodetic networks and also for the purposes of cadastre, land management, agriculture, geophysics. It is monitored with the help of a P-6 controller that is connected by interface cable or via Bluetooth and also with the help of external Android device with special software eSurvey. It is equipped with auxiliary inertial system and electronic level that allow to carry out survey in the localities with difficult conditions.

Delivery set

Smart-antenna МР-10
1 piece
Storage battery
2 pieces
Charging device
1 piece
Adapter for memory device with a set of connectors
1 piece
VHF antenna
1 piece
GSM antenna
1 piece
1 piece
Plate for height measuring
1 piece
Cable for data receipt-transfer
1 piece
Post for fixation of smart antenna
1 piece
Rotary adapter
1 piece
Quick-detachable adapter
1 piece
1 piece
Disk with software  
1 piece
1 piece


Performance Characteristics
Number of channels
A wide range of communication modules
Ethernet; Wi-Fi; Bluetooth V2.1; radio modem
Record frequency
1Hz, 2Hz, 5Hz
Ergonomic design
Compactness and light weight due to the use of modern materials (magnesium alloy, monoblock case components from composite materials)
High degree of protection against mechanical damage
Received signals of satellites:
GPS: L1, L2
Built-in auxiliary inertial system

Accuracy of measurements
Static accuracy
(plan) 3 mm + 1 mm/km
(height) 5 mm +1 mm/km
Accuracy in kinematics
(plan) 10 mm + 1 mm/km
(height) 20 mm +1 mm/km
Accuracy of survey in slope
10º slope of RMS error 20 mm
20º slope of RMS error  30 mm
30º slope of RMS error 50 mm
Hardware features
Dimensions (WxDxH)
114mm х 114mm х 144mm
1,37 kg
Operating temperature
from -30 °С to  +65 °С
Storage temperature
from -40 °С to  +80 °С
Relative to 98%
Air tightness
Shock and vibration resistance
Is tested and is in compliance with the standards of protection from environmental influence
Electrical characteristics
DC Power Supply Voltage
7.4 V rechargeable battery
external source from 9 V to 18 V
Operation time
8 hours

Communication and data storage

  • Serial connection
  • USB v2.0: support for data download and high-speed connections
  • USB-radio modem with frequency band 433-450 MHz
  • Built-in GSM-modem
  • WiFi: 802.11 b, g, access point and client modes, WPA / WPA2 / WEP64 / WEP128 encryption
  • External devices for receiving / transmitting data - via serial port, USB port and Bluetooth
  • Built-in memory 4 GB + microSD slot, up to 32 GB

Scope of delivery

  • Rechargeable battery
  • Charger
  • An adapter for the charger  (for connection to power grids in the Russian Federation)
  • VHF antenna
  • GSM antenna
  • Tape-measure
  • Plate (for height measurement)
  • Cable for data reception and output
  • Transport case
  • Stand for fastening the smart antenna
  • Rotary adapter
  • Quick release adapter
  • Passport
  • StaticToRinex Software (on CD)
  • GGO Software (on CD)
  • Instruction manual (on CD).


The smart antenna comes with built-in software. This software allows to carry out the measurement in the field. The software also includes post-processing software: "StaticToRinex" and "GEO Geomatics Office" (GGO), installed on a PC. This software provides for the smart antenna modules interfacing, setting up and controlling the workflow, storing and transmitting the measurement results, and post-processing of the measured data. Software protection against unintentional and deliberate changes corresponds to the "High" level in accordance with R 50.2.077-2014.